Support
Write to support@ambiguouslabs.net. Please include the App ID shown on the watch under About › Support › Contact Us: that is how we find your watch, as we hold no name or e-mail for it.
Something went wrong during a walk? About › Support › Send Report sends us the watch's log. Quote the report number it shows.

The ANT+ icon
Top of the screen. The radio link to your partner's watch, about 10m.
![]() | Green: your partner's watch is connected. |
![]() | Orange, blinking: looking for your partner's watch. Come closer; it keeps trying. |
![]() | Orange: a short pause between two searches. The next search starts by itself. |
![]() | Red: the watch cannot search: no Partner ID yet, or no radio channel free. Set the Partner ID first. |
| No icon: Partner Walk is Off, or the Sharing Method is Internet Only. |

The globe
Bottom, left of the battery. Your own internet connection, through your phone. Shown while Partner Walk uses the internet or Group Walk is On.
![]() | Green: connected, and fresh data arrives from your partner or your group. |
![]() | Blue: connected, but nothing new from the others yet. Wait a moment, or check their watch. |
![]() | Red, blinking: trying to connect, no answer yet. It often settles within seconds. |
![]() | Red: nothing gets out. The phone is not connected to the watch, or Walk+ is not active (About › Support › Walk+). |

The GPS satellite
Bottom, right of the battery. Your own GPS. Always shown: the GPS starts when the app opens.
![]() | Green: good position. |
![]() | Yellow: weak position. Distance and direction are less precise. |
![]() | Red, blinking: searching for satellites. Go outside with a clear view of the sky; the first fix after a long break can take a few minutes. |
![]() | Red: the GPS could not start. Close Walk Together and open it again. |
On the compass screen the three icons sit together above the name, in the middle.
Questions we get
How do I pair with my partner?
Each watch must know the other's ID. Easiest: stand next to each other and open Sharing Settings › Partner Config › Pair Now on both watches. Each shows the other's ID; confirm it. Or type it in: your own ID is My ID under Partner Config, and your partner enters it as their Partner ID (and you enter theirs). Pairing works both ways: a watch that has not entered your ID back shows "partner not paired". My ID never changes, so you pair once.
ANT+, internet, or both?
Partner Config › Sharing Method chooses how Partner Walk reaches your partner:
- ANT+ and Internet (the default): the radio when you are close, the internet when you are apart.
- Internet Only: through your phones, at any distance.
- ANT+ Only: no phone, no internet; heart rate only, within about 10m.
Calories, steps and location travel over the internet only, so with ANT+ Only you see your partner's heart rate alone.
I cannot see my partner's or a friend's arrow
Look at your globe first.
- Red globe: nothing reaches you. Your phone is not nearby or has no coverage; fix that first.
- Green globe and "no location yet": their watch has no GPS position yet, or their sharing is Off.
- "location not shared": your partner switched off Share Location under Partner Config.
- "out of range": they are farther away than the sharing distance (Location Range) they chose. Within it, the arrow appears.
- "last seen 3 min ago" and a dotted arrow: their watch stopped sending. Their phone is out of reach, or they closed the app. The arrow points to where they were last.
How far does location sharing reach?
Each watch sets its own distance under Sharing Settings › GPS Config › Location Range, from 10m up to 3km (1km unless you change it). Your range decides who may see you; theirs decides whether you see them.
How do we walk as a group?
Everyone enters the same Group Name and Group Key under Sharing Settings › Group Config, then switches Group Walk On. Anyone with the same name and key is in the group, so share them only with the people you walk with. To remove someone, change the key and tell the others.
The watch says "no phone" although the phone is next to it
The link between the watch and the phone is down, whatever the phone says. Open Garmin Connect on the phone; if that does not help, close Walk Together and open it again. "No internet" is different: the phone is connected but has no data. Check mobile data or Wi-Fi.
The GPS takes long to find a position
Walk Together starts the GPS as soon as it opens, so give it the time it takes to walk out of the door. If a position stays weak, try another setting under GPS Config › Satellites; the watch's own setting is the default.
The watch asks to calibrate the altimeter when the app starts
That page is the watch's own. It shows at the start of every activity that uses GPS (Garmin's Walk and Run do the same) when automatic calibration is off. To stop it, open the watch's settings, find Altimeter and switch automatic calibration On.
Is it really free? What is Walk+?
Yes. Walk+ is the name of the internet sharing. It switches itself on the first time the app starts, with no code and no account; About › Support › Walk+ shows its status. The relays cost money to run, so a coffee is welcome but not required.
I have a new watch
The new watch has a new My ID, so pair with your partner again.
Can I use it without a phone?
Yes. Your heart rate, zones, distance, pace, laps, alerts and saving the walk all work without a phone, and so does your partner's heart rate over ANT+. Calories, steps and location from your partner, and Group Walk, travel through the Garmin Connect app on your phone, so for those the phone must be nearby and online.
Delete my data
On the watch: About › Support › Walk+ › Deactivate. The internet sharing stops at once (Partner Walk carries on over ANT+ only, Group Walk goes Off) and what the relay holds about you is deleted within a day. Details in the privacy policy.





